TOBO STEEL GROUP CHINA
TOBO STEEL GROUP CHINA
Add to Cart
DN3000 Single Flanged Butterfly Valve,DIN Flanged Butterfly Valve,15.2MPa Ductile Iron Butterfly Valve |
| Product Name: | Single Flange Butterfly Valve | Size: | DN50 ~DN3000 |
|---|---|---|---|
| Standard: | DIN / BS / AWWA / JIS | Temperature: | -20~120 C |
| Body: | Cast Iron/ Ductile Iron/ Stainless Steel | Automatic: | Yes |
| High Light: | DN3000 Single Flanged Butterfly Valve,DIN Flanged Butterfly Valve,15.2MPa Ductile Iron Butterfly Valve | ||
Automatic Single Flange Butterfly Valve Good Regulation Performance
Single Flange Butterfly Valve Application
The butterfly valve is suitable for fresh water, sewage, seawater, brine, steam, natural gas, food, medicine, oil, various acids and alkalis and other pipelines which require complete sealing, zero leakage in gas test, high life requirement and working temperature between - 10 and 150 degrees.
Product Advantages:
1. This valve is a patented product of the company. The side flange of the product conforms to various pressures of various domestic and international standards.such as national standard, GB,GOST,ANSI,BS,JIS, etc. The connection is convenient and adaptable widely, which can reduce the types of purchase and stocking.
2. The wall thickness of the valve body meets the requirements of GB 26640, the thickness is thick, and the bearing strength is guaranteed.
3. The valve body is made of ductile iron material, spheroidization rate is 3 grades, the mechanical properties are stronger, the tensile strength is 450Mpa, and the elongation rate is more than 10%. Compared with gray iron body, the same thickness tensile strength is gray iron body. 2 times, the applicable working pressure is higher.
4. The valve seat uses imported rubber raw materials, containing 50% of rubber, Shore A hardness of 73 ± 3, tensile strength ≥ 15.2MPa; elongation at break ≥ 350%, valve sealing is reliable, opening and closing torque is stable, seat durable and long life, the number of opening and closing can reach more than 10,000 times.
5. The valve seat is a wide-side , the sealing surface is wider, the valve end seal is easier to guarantee, and the sealing is more reliable. The wide-side valve seat facilitates the installation of the valve, and has a wide contact surface with the flange boss on the pipe, and the sealing performance is reliable. Installation accuracy requirements are lower than for narrow side seats. The valve seat has a concave groove in the axial direction and is equipped with an O-ring, which can realize the secondary sealing of the valve seat in the axial direction.
Butterfly Valve APPLICABLE STANDARDS
1. Design according : API 609
2. Test standard according: JIS B2003
3. Connect flange standard according: JIS B2212
5. Item Name of part Material Spec
| NO | Part name | Material |
| 1 | Body | SS304 |
| 2 | Gear box | Assembly |
| 3 | Disc | SS304 |
| 4 | Stem | SS416 |
| 5 | Seal ring | 316+Graphite |
| 6 | packing | Graphite |
6. Operation:
6.1. The two pipe flange should be smooth.
6.2. Put the butterfly valve in the pipe line, fixed the orientation hole first.
7. Delivery:
When delivery or store the butterfly valve, should keep in dry and cool environment.
8. Note:
8.1. Pipe flange should same as the butterfly valve flange.
8.2. Check the valve before installed, the environment should correspond to the butterfly valve
specification.
8.3. Before open butterfly valve, checking the disc without dirt.
8.4. The disc must be shut off place when installed.
8.5. Adjusting the pipe connect before installed.
8.6. The connect flange should be parallel.
8.7. After installed, the pressure test disc should be open place.
8.8. If the butterfly can not natural open or close, please kindly check it careful, can not strike, tamp or
use extension lever.
8.9. When maintenance or operation, must check the stem, lever, gear box or actuator have correctly
connect. Otherwise the stem will be push by pipe pressure.
9. The malfunction and resolving:
| malfunction | whys | solution |
| Seal leak | 1, Some rubbish on the seal 2, Seal have been light damage | ① Clean the rubbish. ② Replacing the disc |
| Stem Packing leak | 1, packing be damaged 2, packing lapse | ① Tighten the gland nut ② Change the packing |
| flange leak | 1, the nut release 2, gasket lapse | 1 . Tighten the nut 2. Change the gasket |
10. Maintenance
Open the worm box cover and add some butter per two months.
Check the seal, packing and flange, if leak, please maintain ASAP.
Specifications:
Size: DN50 - 3000
Temperature: -15℃ - 150℃
Pressure: 1.0MPa/1.6MPa
Materials
Materials of Body : Ductile Iron (GGG40, GGG50). Cast Iron (GG25), Stainless Steel
Materials of Disc : Stainless Steel. Nickel Plated, Ductile Iron, Ductile Iron Coated Plastic,
Titanium Steel, Copper Alloy etc
Wafer Rubber Seated Butterfly Valves
| DN (mm) | PN (MPa) | Connection dimensions(mm) | |||
| L | D | D1 | Zφd | ||
| 40 | 1.0/1.6 | 43 | 145 | 110 | 4-18 |
| 50 | 43 | 165 | 125 | 4-18 | |
| 65 | 46 | 185 | 145 | 4-18 | |
| 80 | 46 | 200 | 160 | 4-18/8-18 | |
| 100 | 52 | 220 | 180 | 8-18 | |
| 125 | 56 | 250 | 210 | 8-18 | |
| 150 | 56 | 285 | 240 | 8-22 | |
| 200 | 60 | 340 | 295 | 8-22/12-22 | |
| 250 | 68 | 395/405 | 350/355 | 12-22 | |
| 300 | 78 | 445/460 | 400/410 | 12-22 | |
| 350 | 1.0 | 78 | 505 | 460 | 16-22 |
| 400 | 102 | 565 | 515 | 16-26 | |
| 450 | 114 | 615 | 565 | 20-26 | |
| 500 | 127 | 670 | 620 | 20-26 | |
| 600 | 154 | 780 | 725 | 20-30 | |
| 700 | 165 | 895 | 840 | 24-30 | |
| 800 | 190 | 1015 | 950 | 24-33 | |
| 900 | 203 | 1115 | 1050 | 28-33 | |
| 1000 | 216 | 1230 | 1160 | 28-39 | |
| 1200 | 254 | 1455 | 1380 | 32-39 | |
| 1200 | 0.6/0.25 | 254 | 1400/1375 | 1340/1320 | 32-34/32-30 |
| 1400 | 279 | 1620/1575 | 1560/1620 | 36-34/36-30 | |
| 1600 | 318 | 1820/1785 | 1760/1730 | 40-34/40-30 | |
| 1800 | 356 | 2045/1985 | 1970/1930 | 44-41/44-30 | |
| 2000 | 406 | 2265/2185 | 2180/2130 | 48-48/48-30 | |
